top of page

2100 180° Standard

Pump Features:

• straight through T&E cast housing with 2” inlet & outlet.

• Available with optional nitrided housing, Teflon seals, outboard gear case assembly, or direct drive hydraulic motor mount.

• 2” threaded flanges.

• 4” helical-cut, nitrided steel gears.

• Requires a minimum 2” hose & fitting.

Part Numbers:

• 513W             2” T&E 180° cast housing/steel gears/bushing caps/black gaskets 

513WNT      2” T&E 180° nitrided housing/steel gears/Teflon seals/blue gaskets

513W-OBF 2” T&E 180° with outboard gear case assembly

513WD          2” T&E 180° with direct drive hydraulic motor mount

Horsepower Requirements:

• Hydraulic Motor 20hp - 104 Series Recommended      

• Electric Motor 5-10hp with 440 VFD

• Electric Motor 15-20hp with 440 VFD

Recommended Operating Procedures:

• Maximum Temp: 212°F (regular seals)

• Maximum RPM: 750 RPM at the pump

• Maximum Pressure: 125 PSI

Note: pump pressure is maximum safe operating pressure, not the maximum pressure the pump will produce.
Tested Flow Rates:
Installation Dimensions:

4000 180° Standard

Pump Features:

• straight through T&E cast housing with 4” inlet & outlet
• Available with optional nitrided housing, Teflon seals, outboard gear case assembly, or direct drive hydraulic motor mount
• 4” steel weld flanges
• 6” helical-cut, nitrided steel gears
• Requires a minimum 3” hose & fitting
• Eco Pump Option available with Rubber Gears (See ECO Pump)

Part Numbers:

110W              4” T&E 180° cast housing/steel gears/bushing caps/black gaskets
110WNT       4” T&E 180° nitrided housing/steel gears/bushing caps/Teflon seals/ blue gaskets
110WD          4” T&E 180° with direct drive hydraulic motor mount
110W-OBF  4” T&E 180° with outboard gear case assembly

Horsepower Requirements:

• Hydraulic Motor 30-40hp - 109 Series recommended
• Electric Motor 15-20hp with 440 VFD

Recommended Operating Procedures:

• Maximum Temp: 212°F (regular seals)

• Maximum RPM: 750 RPM at the pump

• Maximum Pressure: 125 PSI

Note: Pump pressure is maximum safe operating pressure, not the maximum pressure the pump will produce.
Tested Flow Rates:
Installation Dimensions:

4000R 90° Standard

Pump Features:

• Small body right angle T&E cast housing with 4” inlet & outlet
• Available with optional nitrided housing, Teflon seals, outboard gear case assembly, or direct drive hydraulic motor mount
• 4” steel weld flanges
• 7.5” helical-cut, nitrided steel gears
• Requires a minimum 3” hose & fitting

Part Numbers:

114RW              4” T&E 90° cast housing/steel gears/bushing caps/black gaskets.
114RWNT       4” T&E 90° nitrided housing/steel gears/bushing caps/Teflon seals/ blue gaskets.
114RWD          4” T&E 90° with direct drive hydraulic motor mount.
114RW-OBF  4” T&E 90° with outboard gear case assembly.

Horsepower Requirements:

• Hydraulic Motor 30-40hp - 109 Series recommended
• Electric Motor 15-20hp with 440 VFD

Recommended Operating Procedures:

• Maximum Temp: 212°F (regular seals)

• Maximum RPM: 750 RPM at the pump

• Maximum Pressure: 125 PSI

Note: Pump pressure is maximum safe operating pressure, not the maximum pressure the pump will produce.
Tested Flow Rates:
Installation Dimensions:

4100 180° Standard

Pump Features:

• straight through T&E cast housing with 4.5” inlet & outlet

available with optional nitrided housing, Teflon seals, outboard gear case assembly, or direct drive hydraulic motor mount
• 5” steel weld flanges
• 7.25” helical-cut, nitrided steel gears
• Requires a minimum 4” hose & fitting

Part Numbers:

216RW            5” T&E 180° cast housing/steel gears/bushing caps/black gaskets
216WNT         5” T&E 180° nitrided housing/steel gears/bushing caps/Teflon seals/ blue gaskets
216WD            5” T&E 180° with direct drive hydraulic motor mount
216W-OBF   5” T&E 90° with outboard gear case assembly

Horsepower Requirements:

• Hydraulic Motor 50-60hp - 112 Series recommended
• Electric Motor 20hp with 440 VFD

Recommended Operating Procedures:

• Maximum Temp: 212°F (regular seals)

• Maximum RPM: 750 RPM at the pump

• Maximum Pressure: 125 PSI

Note: Pump pressure is maximum safe operating pressure, not the maximum pressure the pump will produce.
Tested Flow Rates:
Installation Dimensions:

“Our mission is to Design & Manufacture pumps that consider the users, the industry and environment and to provide great service to our customers”

CONTACT US

Call: 844 577 3825
Email: admin@tepumps.com
Visit: 6566 Township Road 370

Consort, AB, Canada 

T0C1B0

4100 90° Standard

Pump Features:

• small body right angle T&E cast housing with 5” inlet & outlet
• 5” steel weld flanges
• 7.25” helical-cut, nitrided steel gears
• Requires a minimum 4” hose & fitting

Part Numbers:

• 214RW   5” T&E 90° cast housing/steel gears/bushing caps/black gaskets

Horsepower Requirements:

• Hydraulic Motor 50-60hp - 112 Series recommended
• Electric Motor 20hp with 440 VFD

Recommended Operating Procedures:

• Maximum Temp: 212°F (regular seals)

• Maximum RPM: 850 RPM at the pump

• Maximum Pressure: 125 PSI

Note: Pump pressure is maximum safe operating pressure, not the maximum pressure the pump will produce.
Tested Flow Rates:
Installation Dimensions:
bottom of page